Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: TypeSH
Showing results 1 to 25 of 487
Search took 1.49 seconds.
Forum: Honda Accord (1990 - 2002)
09-30-2005, 12:31 PM
Replies: 0
Views: 310
Posted By TypeSH

92 LX Auto tranny problems

Posting for a friend of mine:


The car has had hard/rough shifting since getting it, 4 years ago, but nothing serious.

2 days ago I drove it ~450 miles from L.a to Davis, ca and about 10...
Forum: Honda Accord (1990 - 2002)
02-22-2005, 09:01 PM
Replies: 2
Views: 684
Posted By TypeSH

Problem w/ starter cranking non-stop when car is off.

Friend of mine has a big problem on his 92 Accord LX automatic.

Turned on the car, and the car idled rough. So he turned it off and restarted the car and it was idling rough again, so he turned it...
Forum: Honda Accord (1990 - 2002)
12-27-2004, 10:31 PM
Replies: 12
Views: 2,166
Posted By TypeSH

Re: (iam7head)

http://www.hondaautomotiveparts.com/catimgs/13SV20_J10.gif

I ordered parts 8 and 9 there, the boot and the circular clip, listed as the same one for the tie rods. It's honda automotive parts, so...
Forum: Honda Accord (1990 - 2002)
12-25-2004, 01:42 PM
Replies: 12
Views: 2,166
Posted By TypeSH

thanks! now what type of grease do i repack...

thanks!

now what type of grease do i repack the joint with when replacing the boots? and do i pack as much as possible in, or is there some specific amount?
Forum: Honda Accord (1990 - 2002)
12-24-2004, 11:40 PM
Replies: 12
Views: 2,166
Posted By TypeSH

Upper Ball Joints - How to check for damage/How to replace the boots?

on a 94 accord EX:

So I find that both of my upper ball joint boots are leaking grease on the car. I do have a spare set of UCAs, but the boots are ripped on the both of them as well. I think they...
Forum: Honda Accord (1990 - 2002)
06-15-2004, 01:22 PM
Replies: 7
Views: 13,419
Posted By TypeSH

Re: (STARRMAN85)

cotter pin could have been installed improperly and thus fell/broke off too. Or the nut wasn't torqued down properly to begin with. lots of possibilities, sucks to hear it happened though
Forum: Honda Accord (1990 - 2002)
06-15-2004, 01:17 PM
Replies: 7
Views: 519
Posted By TypeSH

Re: 400$ to change a bearing? (RotaryBzzzz)

It's around $40-50 USD for a OEM bearing, and about $30 for a new hub (well thats the price for a 98-99 2.3 CL hub). You don't need a new hub though unless yours is damaged. I dont know how much that...
Forum: Honda Accord (1990 - 2002)
04-18-2004, 03:42 AM
Replies: 6
Views: 3,506
Posted By TypeSH

Re: Tire air pressure (D16Z6racing)

if you have the factory tire size on it, you should stick to what honda recommends. I generally go 2-3 psi higher than the recommended though. It gives me a leeway period when air runs out and I'm...
Forum: Honda Accord (1990 - 2002)
04-08-2004, 02:29 AM
Replies: 3
Views: 415
Posted By TypeSH

Re: master cylinder upgrades and fitment (pyrojeff)

for 5th gen accords, theres the non-ABS master cylinder and the ABS master cylinder. 15/16" for non-ABS one, 1" for ABS one.

the 1" abs one is the same size as the prelude ones, so theres no point...
Forum: Honda Accord (1990 - 2002)
04-03-2004, 01:38 PM
Replies: 20
Views: 1,198
Posted By TypeSH

Re: (StimpyBoy)

if you do go with the 3/4" drive, finding a 3/4" drive 36mm axle socket is kind of hard. If you are gonna try w/ the 1/2" drive socket and use an adapter, try to find an adapter that is very strong...
Forum: Honda Accord (1990 - 2002)
04-02-2004, 07:19 PM
Replies: 20
Views: 1,198
Posted By TypeSH

Re: (SearchBeforeUPost!)

I used a 3/4" breaker bar from harbor freight + 5ft metal pole. Sad part was the cost of the 3/4" drive 36mm socket, like $15. I broke a 1/2" breaker bar so that wasnt gonna work.
Forum: Honda Accord (1990 - 2002)
04-01-2004, 08:48 PM
Replies: 16
Views: 1,177
Posted By TypeSH

Re: (91wagonsir)

answer is no. people have tried, even w/ all the arms, some holes just dont line up (believe specifically the upper A-arms wont fit at all).

you can however swap on the CL hub in place of the...
Forum: Honda S2000
04-01-2004, 08:39 PM
Replies: 16
Views: 5,290
Posted By TypeSH

Re: Anyone have the OEM oil filter wrench tool? (iam7head)

yea, i had a pretty hard time getting it off by hand because my hand just slides off the filter because its so smooth. And to tighten i usually have a little oil on my hands after changing the oil so...
Forum: Honda S2000
03-31-2004, 09:10 PM
Replies: 16
Views: 5,290
Posted By TypeSH

Anyone have the OEM oil filter wrench tool? (or which brand/type do you use)

I need a wrench tool for the filter, but from this picture
http://www.handa-accessories.com/filterwrench.jpg

at honda-accessories of the OEM filter wrench they sell, I can't determine how...
Forum: Honda Accord (1990 - 2002)
03-30-2004, 02:04 AM
Replies: 2
Views: 337
Posted By TypeSH

Re: Brakes question!! (Nathan007)

how hard depends on whether you have bolts that are stuck or not. The 4 bolts going thru the hub to the rotor were frozen so I had a hell of a time getting them apart.

for the bearing, easiest way...
Forum: Honda Accord (1990 - 2002)
02-07-2004, 06:04 PM
Replies: 5
Views: 1,274
Posted By TypeSH

Re: Best place to get a new starter?? and can you just replace the starter solenoid? (SOHCMAN)

when mine went out, out of kragen, autozone and napa in my area, napa had the cheapest one at around $120-130 i believe. Autozone wanted 160 or so, kragen about the same. OEM one from...
Forum: Honda Accord (1990 - 2002)
01-05-2004, 02:05 AM
Replies: 12
Views: 513
Posted By TypeSH

Re: Please post your personal experience with 16'' rims and a 1'' drop (6th gen)...want to prove the

search for "offset calculator" in yahoo and enter the wheel sizes. Go out and measure for yourself.

205 tire for a 7" wide? maybe you should drop to 6.5 or go with a 215/225 tire.
Forum: Honda Accord (1990 - 2002)
12-11-2003, 11:27 PM
Replies: 8
Views: 535
Posted By TypeSH

Re: 94-95 ex sudden oil loss (Slain)

common problem, balancer shaft seal backs out, dropping all the oil. There was a dealer recall for this.
Forum: Honda Accord (1990 - 2002)
12-03-2003, 10:20 PM
Replies: 55
Views: 13,301
Posted By TypeSH

Re: oil filter (jweller)

maybe its just the canadian ones then.
Forum: Honda Accord (1990 - 2002)
12-03-2003, 01:30 PM
Replies: 55
Views: 13,301
Posted By TypeSH

Re: oil filter (knowtomorrow3001)

i need to get a filter wrench for the S2000 filter, its larger in diameter than the regular accord one. It has more filter size, and its made in japan as mentioned above. THe other honda OEM filters...
Forum: Honda Accord (1990 - 2002)
12-01-2003, 12:44 PM
Replies: 7
Views: 468
Posted By TypeSH

Re: Grinding 5th (Spartanic)

its a common problem. it doesnt only happen to those who drive hard, bad design. There's a TSB w/ repair info on it online somewhere.
Forum: Honda Accord (1990 - 2002)
11-30-2003, 08:51 PM
Replies: 13
Views: 1,136
Posted By TypeSH

Re: Guys i need some serious explanation on Vtec. (poid)

somewhere between 2-3k, maybe it was 2500-3k, i forgot.

you should feel power peak at 4000-4400rpm because that is peak torque. 5500rpm is peak HP but it doesnt pull as hard as 4000-4400rpm where...
Forum: Honda Accord (1990 - 2002)
11-30-2003, 08:44 PM
Replies: 55
Views: 13,301
Posted By TypeSH

Re: oil filter (david90)

I paid $6/each (or 6.50) for my S2000 honda oem filters (that i'm using on the accord). So I guess at $2/quart of oil it owuld be about that price, but you can get oil/filters cheaper if u really...
Forum: Honda Accord (1990 - 2002)
11-19-2003, 01:56 AM
Replies: 5
Views: 816
Posted By TypeSH

Re: Anybody use Mitchell On Demand?? (2+2=5)

honda = helms

helms is pretty good for all basic stuff. the only thing it does not cover are the service bullitens and updates/fixes that are developed later on. I think you can order those too,...
Forum: Honda Accord (1990 - 2002)
11-18-2003, 01:34 PM
Replies: 10
Views: 1,853
Posted By TypeSH

Re: Master Cylinder/Brake fade (Showoff)

they are the same size, 1". the accord EX one is probably cheaper.
Showing results 1 to 25 of 487
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 03:12 PM.