Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: kranked91dx
Showing results 1 to 25 of 497
Search took 1.59 seconds.
Forum: Forced Induction
07-21-2012, 04:49 PM
Replies: 42
Views: 14,684
Posted By kranked91dx

Re: which sleeves are better?

I did a few build on GE sleeve, good stuff.
I did quite a few build, about 5, on Darton sleeve, good stuff too.

I personally own a Benson block, built by Earl Laskey at the time... Good stuff,...
Forum: Forced Induction
05-10-2012, 10:53 AM
Replies: 149
Views: 44,030
Posted By kranked91dx

Re: (BALLIN H22 EK)

Sir,
you got an order in the mail at Sales@kinetic...
from Stetcher@hotmail...

let me know it turns out.

thank's
Kranked
Forum: Welding / Fabrication
05-03-2012, 09:01 PM
Replies: 417
Views: 129,873
Posted By kranked91dx

Icon3 Re: You DIY your own crossmember/traction bar setup! post details/pics here

Hell yhea !

I'm the originator of this thread ! it's really a good one to see it back at the top.

I am amazed to see how much valuable information came trough all this.

keep it alive,...
Forum: Tech / Misc
03-16-2012, 03:20 PM
Replies: 1
Views: 2,634
Posted By kranked91dx

Re: Rebuild kit, best place to buy them ?

What !!
198 view and not a single comment !
damn ! you guy's got to know a few re-seller I don't know.

maybe this post is in the wrong place,

Mod's feel free to move the post if you can...
Forum: Welding / Fabrication
03-14-2012, 06:51 PM
Replies: 14
Views: 6,808
Posted By kranked91dx

Re: Proper use of helium in tig welding

I used it before with very good result on my Syncrowave 200.

it does take less amperage to get to the same penetration, and clean very well too.

I used premixed gas, available from my gas...
Forum: Tech / Misc
03-14-2012, 03:50 PM
Replies: 1
Views: 2,634
Posted By kranked91dx

Icon2 Rebuild kit, best place to buy them ?

Hi !
I am fully rebuilding a B18C1 at the moment,
I would like to know where you guy's recommend buying rebuild kit ?

kit's need to include the following :
Pistons, rings, crank and rod...
Forum: Welding / Fabrication
02-20-2012, 05:29 PM
Replies: 1,447
Views: 610,214
Posted By kranked91dx

Re: Starting my own fab shop!

Sorry to hear that,

my shop story came to an end, just like many of us, I did a lot 3 years ago, but I lacked space and time.
since my main job was about 6 month a year at that time, I though...
Forum: Welding / Fabrication
02-20-2012, 04:52 PM
Replies: 5
Views: 2,196
Posted By kranked91dx

Re: fabricator school ? Or own personal tig welder ? choices...

When I started in all this, It was all Stick welding mainly on Agricultural machinerie, then I went trough a few autobody job for me and my friends, then I thought MIG was the best thing on earth,...
Forum: Forced Induction
01-25-2012, 06:27 AM
Replies: 18
Views: 3,900
Posted By kranked91dx

Re: Foam filters? yay or nay?

I did, with a Greedy Unit, and I will not recomend it to anyone.
foam got sucked into the turbo, Happy ending for my story, no damage done to engine, but had to get to an extensive look up of the...
Forum: Welding / Fabrication
12-26-2011, 07:48 PM
Replies: 9
Views: 4,008
Posted By kranked91dx

Re: Ideas about how to go from rectangular head port to round manifold runner

Oval and Blend will do the job pretty well !
I have done several manifold that way, same thing for the collector.

Sch 40 is thick, but if you use a carbide bit, be carefull not to remove to...
Forum: Honda CRX / EF Civic (1988 - 1991)
10-31-2011, 03:33 PM
Replies: 16
Views: 1,083
Posted By kranked91dx

Re: Eratic Heat in 89 si , 10 bucks to who can figure it out

I think you should get a look at the proportioning valves on the heater line, near the firewall, where the coolant hose enter into the cab to the heater core.

make shure the buterfly work's...
Forum: Forced Induction
08-07-2011, 07:33 PM
Replies: 13
Views: 1,578
Posted By kranked91dx

Re: Turbo Set Up

Hi !
A setup I made did 322 Whp on a 18G greedy kit, very similar to your setup.

get it to flow better with a 3 inch exhaust, get the boost higher and honestly, it would be a VERY, I mean,...
Forum: Honda CRX / EF Civic (1988 - 1991)
08-02-2011, 05:47 PM
Replies: 9
Views: 4,895
Posted By kranked91dx

Re: JDM Single Stage VTEC D15B- VTEC not working

I would check the ground between your engine and the body.
clean them off good with sand paper, then put some electric grease.
make shure the ECU is grounded to the body as well.
get a look at the...
Forum: Welding / Fabrication
08-02-2011, 05:34 PM
Replies: 10
Views: 1,396
Posted By kranked91dx

Re: Shop Owners: Cost of Improvements

I built a new shop two year ago.
went from 28x40 with 10' high wall to 30x50 with 12' wall and cathedral ceiling with heated concrete slab.

I added a lot of tool to it wich are not added to this...
Forum: Honda CRX / EF Civic (1988 - 1991)
05-31-2011, 09:25 AM
Replies: 9
Views: 4,895
Posted By kranked91dx

Re: JDM Single Stage VTEC D15B- VTEC not working

The correct way to check Vtec solenoid is to measure the coil Resistance, with an Ohmmeter.

if you want to make shure the plunger is working, just put +12V on the single wire of the solenoid to...
Forum: Honda CRX / EF Civic (1988 - 1991)
05-30-2011, 06:44 PM
Replies: 23
Views: 4,153
Posted By kranked91dx

Re: i did a d16 swap now it wont start

Make shure your ECU is getting some 12V,
get a look at the Ground on the Thermostat housing.
make shure all ground are good on the engine too while your at it.
change plug I guess. I would look...
Forum: Honda CRX / EF Civic (1988 - 1991)
05-27-2011, 06:36 PM
Replies: 23
Views: 4,153
Posted By kranked91dx

Re: i did a d16 swap now it wont start

not expecting the worst here but did you take a compression reading on that engine ?
what are the number ?

make shure your injector are firing too, you may have fuel pressure, and fuel pump, but...
Forum: For Sale
04-28-2011, 11:23 AM
Replies: 40
Views: 3,036
Posted By kranked91dx

Re: EVERY SINGLE THING IS BEST OFFER!!!! Garage Cleanout! B&D SERIES. Endyn. B20b blo

Hi Sir,
If you are willing to ship to Canada,
I'm interested in your OBD0 alternator and Endyn catch can setup.

contact me by E-mail, I don't have time to log often onto H-T anymore. ...
Forum: Forced Induction
02-20-2011, 03:29 PM
Replies: 203
Views: 10,438
Posted By kranked91dx

Re: SOHC Ninjas: Do we ALL have overheating/head-lifting issues?

Well I have been on the Honda scene for 15 years now, and 10 where past with a Dseries, 8 years boosted on D, I have had a blast, those engine are inexpensive and fun, but I have my share of Head...
Forum: Forced Induction
02-20-2011, 03:11 PM
Replies: 6
Views: 11,086
Posted By kranked91dx

Re: Nitrous with Turbo (Anyone??)

My D serie setup used n20 to spool the 60-1 on a d16z6 in decent time.
i was using a 50 shot, controlled by a boost pressure switch, with two contact.
one Normally closed ( used to drive nitrous...
Forum: Forced Induction
02-17-2011, 07:03 PM
Replies: 52
Views: 4,715
Posted By kranked91dx

Re: Diesel Fuel

Yupp !
I own a Diesel truck ( 2003, F350. 6.0Lpowerstroke ) to haul my car in it and haull stuff around. Diesel engine today are way more efficient than they where.
they are tough to death, and...
Forum: Forced Induction
02-02-2011, 06:32 PM
Replies: 21
Views: 2,014
Posted By kranked91dx

Re: Finally putting together my kit.. Seeking advice/suggestions

First off, you got a good start.
Think about getting ARP head stud and Cometic MLS head gasket.
for your wide band, get a look at Innovative one, they are the best IMO.
Quicktime got you covered...
Forum: Forced Induction
01-09-2011, 05:19 PM
Replies: 12
Views: 5,428
Posted By kranked91dx

Re: B18 GSR intake manifold restriction??

I am shooting for 500 WHP on P72 Head.
I figured out the stock intake manifold would do it, to a flow point of vue.
to me though, the IAB, and all the webing in the manifold plenum need to be cut...
Forum: Forced Induction
09-05-2010, 05:47 PM
Replies: 3,915
Views: 1,061,882
Posted By kranked91dx

Re: **Official Boosted EF Thread**

Very good tread !!
suscribed !

car : 1991 civic Dx

old setup :
D16Z6
Eagle H beam rod
SRP piston
stock bore, stock stroke,
Forum: For Sale
08-18-2010, 07:23 PM
Replies: 936
Views: 50,573
Posted By kranked91dx

Re: FS: B series & D series parts

If you are willing to ship to Canada and take Paypal.
I'll take the valvecover,

PM me here, or drop me an Email at Stetcher@hotmail.com
to settle the details !
thank's !
jp
Showing results 1 to 25 of 497
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 02:26 PM.