b20 vtec w/ GSR Head???
Anyone have info on/ or experience with this setup in DC2?
setup is 97 B20 Block 97 GSR Head |
Re: b20 vtec w/ GSR Head???
goes together just like any other b series
|
Re: b20 vtec w/ GSR Head???
its good it will run a friend of mine has a b20b with a gsr head pretty much fully bulit and he put out 230whp and 248 tq and it was real quick
|
Re: b20 vtec w/ GSR Head???
10-4 its got a flat torque line thru the rpms :scared:
|
Re: b20 vtec w/ GSR Head???
slightly faster than a stock itr even with the smaller gsr cams. these often have a short life though. one of my friends created one from a wrecked crv they had at his work. wound up running a 14.5@98mph
now on to the bad. the engine made it 3 oil changes before a rod broke the b20 and b18b stock were never designed for 8,000+ rpm |
Re: b20 vtec w/ GSR Head???
Originally Posted by idrivesideways
(Post 42713980)
slightly faster than a stock itr even with the smaller gsr cams. these often have a short life though. one of my friends created one from a wrecked crv they had at his work. wound up running a 14.5@98mph
now on to the bad. the engine made it 3 oil changes before a rod broke the b20 and b18b stock were never designed for 8,000+ rpm yea deff install a block guard!!! b20s have mean cylinder walk after 5k, also if you could get your hands on a 01 b20z2 or the jdm 01 b20b they are the best ones to get. the b20b has the highest compression for b20s |
Re: b20 vtec w/ GSR Head???
I've had this setup before. But only took it to 7800rpm. Lasted awhile but got annoyed of the Frankenstein DD. Gotta love the torque though
|
Re: b20 vtec w/ GSR Head???
hmm that's a thought if you redlined the engine at 7000 the b20 would probably live awhile and you would have a fairly quick car. even if you're down 10-15hp compared to 8000 engine life is drastically increased.
|
Re: b20 vtec w/ GSR Head???
Originally Posted by idrivesideways
(Post 42715184)
hmm that's a thought if you redlined the engine at 7000 the b20 would probably live awhile and you would have a fairly quick car. even if you're down 10-15hp compared to 8000 engine life is drastically increased.
|
Re: b20 vtec w/ GSR Head???
3 Attachment(s)
my buddy jus got this in today!
if your gonna do a b20 this is the one to get!! anyone know if you could us this manifold??? i know it wont fit under the hood but will it run???? its a beast! |
Re: b20 vtec w/ GSR Head???
yea i had a b20 stock block and a gsr head with valvetrain in a dc2. the car ran `14.5 this is with dc5 17in type r rims and with full interior. love the TQ. if anything i have 3 wisco pistons with ls rods for the b20
|
Re: b20 vtec w/ GSR Head???
if u goin to use the b20 head u will have to use a ls mani
|
Re: b20 vtec w/ GSR Head???
block guards are ugly creatures... Essentially you're fixing the top portion of the cylinder from expanding so the middle part of the cylinder actually flexes more and can cause damage... I'm not sure about the cylinder walk issue, but I can imagine it does because of the longer stroke.
On that note, because of the longer stroke, the rods swing side to side further than a short stroke engine... So at least get some beasty rod bolts if you're going to do it... |
Re: b20 vtec w/ GSR Head???
Originally Posted by 94VTECoupe
(Post 42738396)
block guards are ugly creatures... Essentially you're fixing the top portion of the cylinder from expanding so the middle part of the cylinder actually flexes more and can cause damage... I'm not sure about the cylinder walk issue, but I can imagine it does because of the longer stroke.
On that note, because of the longer stroke, the rods swing side to side further than a short stroke engine... So at least get some beasty rod bolts if you're going to do it... And y wouldn't u just use 2 one at the top and on in the middle? |
Re: b20 vtec w/ GSR Head???
block guards help to prevent blown head gaskets from cylinder walk. they are what they are. as always if you want to make a high spinning motor or a lot of whp boosted you go sleeved or dart
|
Re: b20 vtec w/ GSR Head???
buy rods and arp rod bolts for it and your set
|
Re: b20 vtec w/ GSR Head???
Originally Posted by 95skunkedgsr
(Post 42742780)
buy rods and arp rod bolts for it and your set
|
Re: b20 vtec w/ GSR Head???
i have b20 vtec with gsr head dont need a block guard waste of time and money doesnt do anything if your sleeves are gonna crack a block guard wont help.
look into upgrading your rod and rod bolts. either shotpeen or get some forged. im running stock just upgraded rod bolts and i take it up to 8k all day. now i dont leave it at 8 too long and i take care of my motor. if your stuff is built right and you checked and double checked your motor should be good. have faith in your setup and know your limits you should be okay. b20 is good but if you can go lsvtec |
Re: b20 vtec w/ GSR Head???
Originally Posted by GranDaddyPurp
(Post 42750404)
i have b20 vtec with gsr head dont need a block guard waste of time and money doesnt do anything if your sleeves are gonna crack a block guard wont help.
look into upgrading your rod and rod bolts. either shotpeen or get some forged. im running stock just upgraded rod bolts and i take it up to 8k all day. now i dont leave it at 8 too long and i take care of my motor. if your stuff is built right and you checked and double checked your motor should be good. have faith in your setup and know your limits you should be okay. b20 is good but if you can go lsvtec :agree: |
All times are GMT -8. The time now is 10:02 AM. |
© 2024 MH Sub I, LLC dba Internet Brands