DIY: Step-by-step how to paint your valve cover
Did a search and didn't find anything with detailed instructions so here's my write up. Not everyone will do it EXACTLY the same, but this will give you all a general idea on the necessary steps needed to do the job correctly.
1. Get your preferred paint stripper/thinner. I used a can of Air craft paint remover. Worked good. The gel stuff is a bit stronger though. But with a few coats of the spray, a good amount came off. Personally i would rather use the can, its faster and easier to use. Just please, please make sure you wear gloves. My finger was killing me the rest of the day. https://i109.photobucket.com/albums/...Picture020.jpg 2. Once paint is bubbling up, and you have waited about 10 min for paint stripper to work, rinse or wipe off the paint. I used a hose and it did the job. You might have to repeat this process a coupe times if the paint is really thick, or just caked on there. https://i109.photobucket.com/albums/...Picture018.jpg 3. Once done with taking excess paint off, sand it lightly. I forget the grit that i used but it was about 800. Make sure everything is nice and smooth and ready for primer. https://i109.photobucket.com/albums/...Picture019.jpg 4. Now i used the cheap 2.99 primer instead of the 5.99 stuff. Worked just as good. Make sure to spray evenly from left to right or right to left. I put 2 coats of primer to make sure everything was covered give it 1-2 minutes between coats. https://i109.photobucket.com/albums/...Picture022.jpg 5. Let the primer dry for about 5 min. Will dry very quickly. Then get your preferred paint ready to go by shaking it for about 1 min. https://i109.photobucket.com/albums/...Picture021.jpg 6. The most important step is paint. In order to get a nice smooth finish, you need to be patient and not over do it. Coat by coat. When painting make sure to get a few sprays on the card board or floor or whatever your painting on to get an idea as to how far you need to be from the valve cover. Once you have the first LIGHT coat. Let it sit for 10-15 min. DO NOT TOUCH THE PAINT TO MAKE SURE ITS DRY. Although it may be dry on the surface, the paint is still very soft and unless you like seeing your finger print in the paint, dont do it man! Repeat step 6 until you have atained the desired look. https://i109.photobucket.com/albums/...Picture023.jpg https://i109.photobucket.com/albums/...Picture015.jpg Never spray 1 spot only, you must spray from right to left in an even fashion or you will over spray. 7. Now again let the paint dry for another 15 min. Once this is complete, carefully take the valve cover(try not to touch any painted surface if possible.) and stick it in the oven at 215 degrees for 15 min. This will heat treat the paint so it will not chip off. https://i109.photobucket.com/albums/...Picture024.jpg Get a towel or a mitt, take the cover out of the oven, let sit until its not burning your hand off, and enjoy!! This is just one way you can do it. Hope this helps! And just for kicks, the car its going in.... https://i109.photobucket.com/albums/...Picture025.jpg 5. |
Re: DIY: Step-by-step how to paint your valve cover (mitsuman)
good write up https://honda-tech.com/forums/images/smilies/emthup.gif
|
Re: DIY: Step-by-step how to paint your valve cover (GG99)
|
Re: DIY: Step-by-step how to paint your valve cover (1slow_crx)
Cool. Thanks for sharing. https://honda-tech.com/forums/images/smilies/emthup.gif
|
Re: DIY: Step-by-step how to paint your valve cover (shutupnskate)
[cool voice] What can i say, i do what i can. [/cool voice]
|
Re: DIY: Step-by-step how to paint your valve cover (mitsuman)
Nice write-up https://honda-tech.com/forums/images/smilies/emthup.gif
|
LOL at you finger
oh yeah it might be better if you use high temp primer as well. Just so the base coat can with stand the temp. And use High Temp Clear...makes the VC easier to clean when it get greasy https://honda-tech.com/forums/images/smilies/emthup.gif so the spray on shit sucks??? I almost dies using the gel shit freakin gotta wear a mask |
Re: (vega_box)
Good write up man! https://honda-tech.com/forums/images/smilies/emthup.gif
|
good write up.. i should've done a write-up when i did mines 6 months ago..
OT: but why paint the vc yellow again??? |
Re: (DeviousCTR)
Thanks yall for the comments.
Ya I decided not to clear it, dont want it to be too shiny. I repainted it because the first time around I got a couple hairs in it and I didnt have a chance to take step-by-step pictures. The first time, I baked it twice. lol thats probable why it wouldnt come off. https://honda-tech.com/forums/images/smilies/emthup.gif |
Re: DIY: Step-by-step how to paint your valve cover (mitsuman)
nice right up, pics of it in the car?
|
Re: DIY: Step-by-step how to paint your valve cover (efocmacro)
how come you didn't use a high-temp primer?
|
Re: DIY: Step-by-step how to paint your valve cover (efocmacro)
you didnt have to take your head off to paint your valve cover... lol.!
https://honda-tech.com/forums/images/smilies/emthup.gif |
Re: DIY: Step-by-step how to paint your valve cover (9civichatch3)
wait. so it was yellow and you just repainted it?
|
Re: DIY: Step-by-step how to paint your valve cover (mitsuman)
good write up. what about stock valve cover paint? how easy is it to get off?
|
Few steps missing that I would have added, but good write up none the less
|
Re: (Sean @ ESG)
what steps would you have added
|
after the paint was stripped I would have sanded with a more coarse grit of sand paper. 200 or 400 something, 800 is very fine. I sand mine with 200 before prime. After the paint was layed, I would have let it dry and then wet sand with the 800. Then follow with a clear coat.
|
Re: (Sean @ ESG)
i see the mitsu in the back !! https://honda-tech.com/forums/images...s/emsmilep.gif nice write up !
|
Re: DIY: Step-by-step how to paint your valve cover (mitsuman)
would you do 2 colors the same way? like bake the first coat then paint over it and bake again??
|
thnk u..
what if u wanna do more than 1 colour? |
Re: (waddy41)
very good write up bro! does it stink up the kitchen when heatin the vavlve cover https://honda-tech.com/forums/images/smilies/emthup.gif
|
picture of said completed project
|
|
for primer use an epoxy primer...sticks better to metal or self etching...make sure u clean the valve cover very well so no dust is on it when ur painting it
|
All times are GMT -8. The time now is 02:19 PM. |
© 2024 MH Sub I, LLC dba Internet Brands