H22 cnc'd plenum spacer and custom intakes
#1
Honda-Tech Member
Thread Starter
H22 cnc'd plenum spacer and custom intakes
been working on alot of different H series intake designs and parts lately. here is some of my latest work:
the intake below is for a mild boosted setup which will make around 650whp. it would also work great on any N/A setup up to 95mm stroke. shorter runners and increased plenum size w/ no restriction is what makes it work so well.
75mm tb bore
^^ cnc billet spacer can be done in any thickness!!
this next setup is a race manifold for an N/A 90x95mm setup which will make over 300whp
^^90mm tb bore
these next two manifolds are from my own personal race car. the smaller one (shown on right) helped me to make 340whp before selling it and making the larger one (shown on left) completely from scratch which i was running at the end of last season on my 90x100mm setup which made 350whp and ran 10.43 @ 131mph raising the h series allmotor street record even higher
^^more custom cnc plenum flanges the larger manifold has a 105mm tb on it and the smaller manifold has a 90mm tb on it, both w/ custom cnc tb flanges.
im also working on another race manifold w/ custom upper plenum which will keep the tb under the hood in the stock location. this manifold will be tested on a stock bottom end h22 w/ pro2 cams and a few different custom headers. i will post some pics of it when i get around to making it.
just thought id share w/ all you prelude guys, and i believe Dave (crazes) will be testing a manifold in his prelude on his 95mm setup as well pretty soon as well.
the intake below is for a mild boosted setup which will make around 650whp. it would also work great on any N/A setup up to 95mm stroke. shorter runners and increased plenum size w/ no restriction is what makes it work so well.
75mm tb bore
^^ cnc billet spacer can be done in any thickness!!
this next setup is a race manifold for an N/A 90x95mm setup which will make over 300whp
^^90mm tb bore
these next two manifolds are from my own personal race car. the smaller one (shown on right) helped me to make 340whp before selling it and making the larger one (shown on left) completely from scratch which i was running at the end of last season on my 90x100mm setup which made 350whp and ran 10.43 @ 131mph raising the h series allmotor street record even higher
^^more custom cnc plenum flanges the larger manifold has a 105mm tb on it and the smaller manifold has a 90mm tb on it, both w/ custom cnc tb flanges.
im also working on another race manifold w/ custom upper plenum which will keep the tb under the hood in the stock location. this manifold will be tested on a stock bottom end h22 w/ pro2 cams and a few different custom headers. i will post some pics of it when i get around to making it.
just thought id share w/ all you prelude guys, and i believe Dave (crazes) will be testing a manifold in his prelude on his 95mm setup as well pretty soon as well.
Last edited by NAH2B; 01-07-2011 at 07:26 PM.
#2
Honda-Tech Member
Join Date: Aug 2007
Location: florida, united states
Posts: 363
Likes: 0
Received 0 Likes
on
0 Posts
Re: H22 cnc'd plenum spacer and custom intakes
very nice, if your looking for any other test mules let me know. if you search my name on here. i have a turboed h22 made 621whp and i am still on a stock intake manifold and i think there is a lot left on the table. pm me if you want to work something out. thanks
#3
Re: H22 cnc'd plenum spacer and custom intakes
This is what we need to look at guys for sure. These mainfolds I have seen close up and they both produce great power for our motors. I will for sure being testing the mainfold under the hood that Randy is talking about for our cars and will definetly have some info when I get my mainfold and get it to dyno and the track.
Good Job Randy always giving help to your fellow H engine guys
Good Job Randy always giving help to your fellow H engine guys
#5
Honda-Tech Member
Join Date: May 2006
Location: rockford, Illinois, United States
Posts: 206
Likes: 0
Received 0 Likes
on
0 Posts
Re: H22 cnc'd plenum spacer and custom intakes
hey great work those look awesome!! curious to see if you would be willing to just gut my stock manifold take all those cross bars out if so shoot me a pm with a price to do so. your work looks amazing by the way!!
#6
Honda-Tech Member
Thread Starter
Re: H22 cnc'd plenum spacer and custom intakes
Thanks everyone.
the factory runner length is to long for anyone seeking performance from their H22. my design takes a few inches out of the runner by eliminating the grid inside the plenum. this not only shortens the runner but also increases plenum volume and at the same time eliminates all the restriction caused by the grid. i can vary the runner length anywhere between stock and as short as in the pic above while still increasing volume and eliminating restriction. it all depends on the customers application. every setup is different but from what i have personaly seen in dyno testing im sure everyone here will be happy w/ the performace gains. im very confident to say it will outperform the euro r, skunk2 and rbc manifolds hands down.
Dave (crazes) will be testing one soon back to back against his euro r on his 95 stroke motor and J West will be testing a couple of my designs against his skunk2 on his stock bottom end H22 w/ pro 2 cams. im sure both will post the results.
i have done alot of testing in the past w/ the euro r and skunk2 manifolds and i know where they fall short and why depending on each application. when i build a manifold for a customer i build it for their specific application.
the factory runner length is to long for anyone seeking performance from their H22. my design takes a few inches out of the runner by eliminating the grid inside the plenum. this not only shortens the runner but also increases plenum volume and at the same time eliminates all the restriction caused by the grid. i can vary the runner length anywhere between stock and as short as in the pic above while still increasing volume and eliminating restriction. it all depends on the customers application. every setup is different but from what i have personaly seen in dyno testing im sure everyone here will be happy w/ the performace gains. im very confident to say it will outperform the euro r, skunk2 and rbc manifolds hands down.
Dave (crazes) will be testing one soon back to back against his euro r on his 95 stroke motor and J West will be testing a couple of my designs against his skunk2 on his stock bottom end H22 w/ pro 2 cams. im sure both will post the results.
i have done alot of testing in the past w/ the euro r and skunk2 manifolds and i know where they fall short and why depending on each application. when i build a manifold for a customer i build it for their specific application.
Last edited by NAH2B; 01-07-2011 at 07:27 PM.
Trending Topics
#12
Honda-Tech Member
Thread Starter
Re: H22 cnc'd plenum spacer and custom intakes
Thanks everyone, im glad you like them. i have been working hard on these manifolds over the past year and have found they perform far better than other manifolds such as euro r, rbc and skunk2. i do a ton of dyno and track testing throughout each season and was really excited w/ what i found this year when i started making these custom manifolds.
#15
Honda-Tech Member
Join Date: Nov 2010
Location: howard county
Posts: 103
Likes: 0
Received 0 Likes
on
0 Posts
Re: H22 cnc'd plenum spacer and custom intakes
You just lost a paying customer. Just because you have done good things doesn't mean you have the right to **** on the guys trying to come up. I asked for your help you refused to help me. I'll reach my goal with out your help. Thanks for the movitation
#17
Re: H22 cnc'd plenum spacer and custom intakes
congrats. interesting you need someone else to motivate you do reach your goal
#18
Re: H22 cnc'd plenum spacer and custom intakes
here is a quote....
if you dont have haters then you havent done anything worth a crap!!!
so in that respect,im super pumped about these im combo's,,like anyone
else im just short on cash,,but i cant wait too ditch my itb's for this kinda ram set-up
if you dont have haters then you havent done anything worth a crap!!!
so in that respect,im super pumped about these im combo's,,like anyone
else im just short on cash,,but i cant wait too ditch my itb's for this kinda ram set-up
#19
Honda-Tech Member
Thread Starter
Re: H22 cnc'd plenum spacer and custom intakes
sorry but i cant help you there. however i did answer your questions even after you called me stuck up. maybe someone else on here can help you w/ your goal.
#20
Honda-Tech Member
Join Date: Nov 2010
Location: howard county
Posts: 103
Likes: 0
Received 0 Likes
on
0 Posts
Re: H22 cnc'd plenum spacer and custom intakes
Being told I can't just makes me try that much harder.
I don't see what's so funny or impossible about it. I guess I'll find out myself.
#21
B*a*n*n*e*d
Join Date: Nov 2009
Location: Pensacola, FL
Posts: 1,538
Likes: 0
Received 0 Likes
on
0 Posts
Re: H22 cnc'd plenum spacer and custom intakes
#23
B*a*n*n*e*d
Join Date: Nov 2009
Location: Pensacola, FL
Posts: 1,538
Likes: 0
Received 0 Likes
on
0 Posts
#24
Honda-Tech Member
Thread Starter
#25
B*a*n*n*e*d
Join Date: Nov 2009
Location: Pensacola, FL
Posts: 1,538
Likes: 0
Received 0 Likes
on
0 Posts