DualCamDan

Finally Got a New Camera...

New Camera = New Pics!

Phantastic

jdmdrifter - what suspension are you using for your crv?

RevIllusions

1999 Honda CRV EX 5speed

1994 B18C Cylinder Head
1994 B18B Short Block 81mm bore
Golden Eagle VTEC Conversion Kit
ARP Head Studs
Supertech Dual Valve Springs and Titanium Retainers
Wiseco 9.5 Flat top pistons
Eagle H Beam Connecting Rods
ACL/King Bearings
HKS Air Filter
Professional Products 68mm Throttle Body
Skunk2 Black Intake Manifold (port matched)
Skunk2 Cam Gears
Skunk2 Magentic Drain Plugs
Mishimoto Catch Can
ACT 6 Puck Clutch and Pressure Plate
NSX Calipers
TD05-18G Mitsubishi Turbo
GReddy Turbo Manifold and Downpipe
GReddy Front Mount Intercooler
Greddy Turbo Timer
Fast-Turbo turbo oil line upgrade kit
Custom 2.5 inch down pipe
Custom 2.5 inch test pipe
Custom 3.0 inch exhaust
Megan Racing MVO-T 3.0 inch muffler
Hondata 3 BAR Map Sensor
RC440 Injectors
Walboro 255 Fuel Pump
Hondata S300
Mishimoto Radiator and Fans
Autometer Boost Guage
Mugen FG360 Steering Wheel
Mugen Showa Shocks and Springs
RSX Type S wheels

LDForget

sweet man, any idea how much power your making? AWD or FWD? How'd you route your exhaust if AWD? I routed my 3" on the drivers side.

pistol_p

looks sick lowerd

JDMDrifter05

If I recall correctly it is:
Front:
7in x 2.5in 600lb Eibach Spings 0700.250.0550
98-01 DC2 Type-R KYB AGX
97-01 CRV SPC Adjustable Ball joints
Grinded the UCA ends down smooth to avoid getting a control arm stuck, again

Rear:
8in x 2.5in 450lb Stance Springs
94 Eclipse GSX KYB AGX
97-01 CRV SPC EZ Arms
Custom Aluminum Strut Bushing

On a side note, I run with the fronts as firm as they go to avoid fender well rubbing and rears at the 2nd softest setting unless I have people in the back then I go to the 4th softest

KnightX

here's my CRV (DD/beater)

LDForget

You've got the same damn dent in the rear bumper as ive got. i cant wait to swap mine over from my parts CRV.

KnightX

^^ LOL ive been too lazy to pop it out... i had that there since i picked up the car

LDForget

Its not as easy as youd think. I even tried a heat gun to get it warmed up a bit, and it didnt pop out at all.

KnightX

if it doesnt pop out then meh... doesnt really bother me lol

www.megameet.org

I used a heat gun on mine ( same spot before i got the car), and pushed it out from the backside with a hammer. Not perfect, but not dented anymore

gxr154

Here's a pic of my old 97 black awd crv auto i sold to a buddy of mine....dropped with 300 srt8 wheels...

fourbangerfan

fast2camciv and preludepeterr, what did you use to lower you CRV? Also, what size tires are you running? Thanks in advance for any feedback. I'm very impressed with the CRVs on this post!

91 EF DX

Picked this up 2 weeks ago. Only thing I've done is change the radio and put a hitch on it and bought a clock to go in it which I have yet to wire up. Thinking of lifting it or just putting some bigger tires on it.

Elvis Presley

Howdy,

UK based new CR-V owner (1st Gen - 2000) and I'm looking forward to finding out all the stuff I should have found out about before I bought it.

I've been looking for something to help me negotiate some v.steep on-road hills (and the odd track) during my summer holidays in the mountains of Snowdonia. The CR-V seemed to fit the bill.

I'm a 48 yr old with a keen interest in all things car-related. Soft spot for Alfa Romeo. Considered a Suburu Forester/Outback or CR-V. Hopefully I've gone for the right one.

I'll do some searching of the DIY threads, and I might post the odd question.

All the best

Steve

I've been doing a few jobs....

Changed oil
air filter + cabin filter
fitted two sidelight bulbs
cleaned it in and out (smokers car previously)
changed trans fluid
changed 'stat



old air filter -

not clean -

bumper was a lot goosed -

heat gun makes it a bit better? -

leak fixed -

ditched these

for






front windows not working
relay ok
fuses ok
hmmmm
need to test switch and ground

Elvis Presley

oh and I dabbed a bit of solder about and that fixed the clock.

Thanks for reading.

98silverbullets

Qu



Picking up my built B20z/vtec silverbullet and dropping off the b20b turbo project. 2 silver v's at the same damn time!





N/A B20z/vtec





Freshly built minty fresh

Skillachie

Thanks a good looking engine bay right there

jc007_sr

My 97 crv

jc007_sr

Wires in between the door jam will be your problem. Did mines a couple months ago. Pain in the ash!!!!

Stygeon

just wondering what you did for the vtec swap?

colinwerks

Hi, New to the board here. This is my 97 V. Before and after. I put on some painted g35 wheels, lowered about 3", painted and coaxed an S2k Lip on it. Its my daily so i'm keeping it relatively simple for now.

Carbongoat

Anyone have a diy on installing the accord fog lights?

Zack Richwine

Mini range