obd0 to obd1 wiring questions
#1
obd0 to obd1 wiring questions
by looking at my chart that came with my obd0-0bd1 ecu jumper, i know that blue, red, black, and white are supposed to be wired up to a 4 wire o2 sensor. i have the sensor but i cannot figure out what color goes to what pin on the o2 sensor. can someone point a noob in the right direction?
i have a b20 so i am not using the vtec wires: purple, and grey. but why on black does it say vtec pressure switch- o2 sensor?
i have a b20 so i am not using the vtec wires: purple, and grey. but why on black does it say vtec pressure switch- o2 sensor?
#3
Honda-Tech Member
Join Date: May 2008
Location: Concord, CA, USA
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Re: obd0 to obd1 wiring questions
it's a common ground for both the pressure switch and the o2 sensor. I believe it goes to the ecu ground on the thermostat housing.
#4
#5
Re: obd0 to obd1 wiring questions
so does it matter which black wire on my 12 pin ecu jumper plug goes to the o2 sensor? the 12 pin plug has 2 black wires thats whats confusing me
Trending Topics
#8
Re: obd0 to obd1 wiring questions
the rywire harness doesnt have the same wire colors as mine and my o2 sensor doesnt have the same color wires either. that does have some good info though
#10
Keyboard Humorist
Join Date: May 2002
Location: Granada Hills, Ca, USA
Posts: 9,814
Likes: 0
Received 9 Likes
on
7 Posts
Re: obd0 to obd1 wiring questions
It looks like you have white, white, blue (or grey?), black.
Right?
Two whites are heater (doesn't matter which goes where)
Black is signal +
Other color is ground -
Try that.
If you get an O2 code then flip the the black and the blue.
Right?
Two whites are heater (doesn't matter which goes where)
Black is signal +
Other color is ground -
Try that.
If you get an O2 code then flip the the black and the blue.
#11
Honda-Tech Member
Join Date: Oct 2008
Location: Lincoln, WTF, USA
Posts: 477
Likes: 0
Received 0 Likes
on
0 Posts
Re: obd0 to obd1 wiring questions
Thats a universal heated O2 sensor.
Grey is Signal -- D14
Both White is for heater
Black is Ground----GND ECU or Thermostat location.
Grey is Signal -- D14
Both White is for heater
Black is Ground----GND ECU or Thermostat location.
#12
Re: obd0 to obd1 wiring questions
thanks a lot. i got my o2 wired up but now im left with the a23 black, pink, brown, and yellow wires that i dont know what to do with them
#13
Honda-Tech Member
Join Date: Oct 2008
Location: Lincoln, WTF, USA
Posts: 477
Likes: 0
Received 0 Likes
on
0 Posts
Re: obd0 to obd1 wiring questions
Pink = Hooks to A15 on OBD0 and splices into A13 12v+ signal also goes to power up injector box also.
Brown = Ground
Yellow = Check Engine light wire on OBD0 pin B20
Black = Ground on Main relay side
You might want to double check but this should be right since its how i got mine wired up on the conversion harness.
Brown = Ground
Yellow = Check Engine light wire on OBD0 pin B20
Black = Ground on Main relay side
You might want to double check but this should be right since its how i got mine wired up on the conversion harness.
#14
Re: obd0 to obd1 wiring questions
i hooked the pink wire up to a13 and a15
brown is hooked up to a16
black is hooked up to a2
i also replaced main relay and the car wont start. it is not getting fuel to the engine. i never hear the fuel pump prime either when i turn the key. the starter will crank
brown is hooked up to a16
black is hooked up to a2
i also replaced main relay and the car wont start. it is not getting fuel to the engine. i never hear the fuel pump prime either when i turn the key. the starter will crank
Thread
Thread Starter
Forum
Replies
Last Post
Ls1 FD3s
Honda Civic / Del Sol (1992 - 2000)
1
08-27-2007 06:44 PM
nabin
Honda Civic / Del Sol (1992 - 2000)
4
03-16-2007 03:11 AM