dpfi to mpfi. resistor box need with obd1 injectors.
#1
Honda-Tech Member
Thread Starter
Join Date: Aug 2005
Location: SD Thief KiLLER, ca, thief killer
Posts: 2,182
Likes: 0
Received 0 Likes
on
0 Posts
dpfi to mpfi. resistor box need with obd1 injectors.
i need to get started on the dpfi to mpfi injector conversion. i was wonder since i have a wrecked eg. i could use th injector clips and plugs from the old obd1 harness, to do the dpfi 2 mpfi conversion. I shouldn't need to wire in the resistor box, because of the injectors being peak hold. Or is it saturated injectors...
#2
Honda-Tech Member
Join Date: Jun 2002
Location: Emo land, Utah, USA
Posts: 1,235
Likes: 0
Received 0 Likes
on
0 Posts
Re: dpfi to mpfi. resistor box need with obd1 injectors. (dem0nk1d)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by dem0nk1d »</TD></TR><TR><TD CLASS="quote">i need to get started on the dpfi to mpfi injector conversion. i was wonder since i have a wrecked eg. i could use th injector clips and plugs from the old obd1 harness, to do the dpfi 2 mpfi conversion. I shouldn't need to wire in the resistor box, because of the injectors being peak hold. Or is it saturated injectors...</TD></TR></TABLE>
Those injectors you have from the EG are saturdated so you won't need a resistor box.
Those injectors you have from the EG are saturdated so you won't need a resistor box.
#3
Re: dpfi to mpfi. resistor box need with obd1 injectors. (dem0nk1d)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by dem0nk1d »</TD></TR><TR><TD CLASS="quote">i need to get started on the dpfi to mpfi injector conversion. i was wonder since i have a wrecked eg. i could use th injector clips and plugs from the old obd1 harness, to do the dpfi 2 mpfi conversion. I shouldn't need to wire in the resistor box, because of the injectors being peak hold. Or is it saturated injectors...</TD></TR></TABLE>
OBD0=Resistor Box Neede
OBD1=No Resistor Box Needed
Modified by slow_rex_will at 5:43 PM 6/20/2007
OBD0=Resistor Box Neede
OBD1=No Resistor Box Needed
Modified by slow_rex_will at 5:43 PM 6/20/2007
#5
Honda-Tech Member
Re: (cr-x-91)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by cr-x-91 »</TD></TR><TR><TD CLASS="quote">u got it backwards bud
0bd0=resistor box
0bd1=no resistor box</TD></TR></TABLE>
QFT
If you run OBD-1 or OBD-2 injectors all the resistor box wires all need to be wired together in some fashon. You can repin them into the OBD-1 resistor box cap to keep it clean.
0bd0=resistor box
0bd1=no resistor box</TD></TR></TABLE>
QFT
If you run OBD-1 or OBD-2 injectors all the resistor box wires all need to be wired together in some fashon. You can repin them into the OBD-1 resistor box cap to keep it clean.
#6
Re: (cr-x-91)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by cr-x-91 »</TD></TR><TR><TD CLASS="quote">u got it backwards bud
0bd0=resistor box
0bd1=no resistor box</TD></TR></TABLE>
My Fault, Fixed it.
Blame it on the kush!
0bd0=resistor box
0bd1=no resistor box</TD></TR></TABLE>
My Fault, Fixed it.
Blame it on the kush!
Thread
Thread Starter
Forum
Replies
Last Post
HiProfile
Honda CRX / EF Civic (1988 - 1991)
3
06-20-2005 02:34 PM