help putting back tranny
#1
help putting back tranny
guys im putting back my tranny today bolt the torque converta blots on connect up the shifter cable put the car in drive and the converta is not spinning, if i spin the wheel the other wheel spins but not the converta ived tried it in all different gears, i didnt put any tranny fuild as yet can this cause it? if i turn the crank pully it turns the converta but not the wheels the car is on a hoist.
#2
Re: help putting back tranny (mentality)
i didnt do these steps as yet can this cause it.
Install the starter. Connect the cables to the starter. Connect the lock-up control solenoid valve and shift control solenoid valve connectors. Connect the speed sensor connectors and the transaxle ground cable. Connect the transaxle cooler hoses to the joint pipes
Install the starter. Connect the cables to the starter. Connect the lock-up control solenoid valve and shift control solenoid valve connectors. Connect the speed sensor connectors and the transaxle ground cable. Connect the transaxle cooler hoses to the joint pipes
#4
Re: help putting back tranny (mentality)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by mentality »</TD></TR><TR><TD CLASS="quote">... if i turn the crank pully it turns the converta but not the wheels the car is on a hoist.
</TD></TR></TABLE>Sounds like you just turned the crank pulley with a wrench. I hope you didn't start the engine & try it without any oil in the tranny.
</TD></TR></TABLE>Sounds like you just turned the crank pulley with a wrench. I hope you didn't start the engine & try it without any oil in the tranny.
#5
Re: help putting back tranny (JimBlake)
i got the car running today, i pour way too much ATF could this cause harsh shifting? also im using dexron 3, i cannot move the shifter out of park unless i stick the key in that slot and move it. also if i try to put the car in park with it running i can hear the tranny making noises like if something is caught of hooking inside the tranny, maybe this is the reason y the flex plate broke, all other gears are fine.
fluid is at proper level shifting improved just a bit, maybe the tranny is wrone out.
Modified by mentality at 4:08 PM 8/25/2007
fluid is at proper level shifting improved just a bit, maybe the tranny is wrone out.
Modified by mentality at 4:08 PM 8/25/2007
#6
Member
Join Date: Apr 2007
Location: Driving Slow, Through Your City
Posts: 1,260
Likes: 0
Received 0 Likes
on
0 Posts
Re: help putting back tranny (mentality)
i got the car running today, i pour way too much ATF could this cause harsh shifting? also im using dexron 3, ...
Out That, In Some Honda ATF
Out That, In Some Honda ATF
Trending Topics
#8
Re: help putting back tranny (mentality)
Lots of people have told about harsh shifting when using Dexron in place of Honda ATF. Honda says use Dexron as an emergency temporary substitute.
#10
Honda-Tech Member
Re: help putting back tranny (GearSpeedEF7)
If you can put the tranny back into park and it grinds and all you need to check to make sure your axles are locked into the transmission properly. If the lock pin dosen't go in right during the install the axles can slip out causing this....I've experienced this first hand.
#11
Honda-Tech Member
Join Date: Apr 2007
Location: OTown, ks, usa
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
Re: help putting back tranny (mentality)
did you turn the converter three times before you bolted it to the flex plate? and you bolted the flex plate up to the motor right?
Thread
Thread Starter
Forum
Replies
Last Post
Chris_
All Motor / Naturally Aspirated
8
06-20-2004 04:01 PM