Originally Posted by larueminati

hi, im attempting to install a viper 5704 alarm system on auto 96 integra and i need help to figure out what wires/connections do not need to be used and where some wires go. feel free to make corrections if i am wrong, and please help answer some of my questions (in bold)

thank you in advance

(took this list from Orange_SIR1)

Main Harness 6 pin

h1/1 red const 12v - tap to a const 12v source
h1/2 black grnd - chassis ground
h1/3 brown siren out - connect to direct to siren
h1/4 white/brown park light isolation wire - is this needed?-Not needed
h1/5 white park light out - tap to park lights
h1/6 orange ground when armed output - where to ground this? Not needed unles you plan on adding extra kills or accesories

Door lock 3 pin

1 blue out - tap to neg unlock
2 n/a
3 green - tap to neg lock

Aux/shutdown/trigger harness, 24 pin

h2/1 pink/white ign/flex relay out - where to tap this? Not needed
h2/2 black/white neutral safety input - tap to e brake? E brake for saftey. At ebrake or behind cluster
h2/3 blue white 2nd stat/rear defog out - tap to defogger
h2/4 green black oem alarm disarm out - n/a
h2/5 red/white trunk release out - tap to trunk release
h2/6 green door trigger input (-) - tap this to where? Driver door pin, driver a pilliar
h2/7 black/yellow dome light supv out - connect to relay/lights
h2/8 brown/black horn honk - tap to horn
h2/9 dark blue status out - where to connect this? Not needed unless using a back up battery moduel
h2/10 pink ign out - where to connect this?not needed
h2/11 white/black aux3 out - n/a
h2/12 violet (+) door trigger in - where to connect this?not needed
h2/13 white/violet aux1 out - n/a
h2/14 violet/black aux2 out - n/a
h2/15 orange/black aux4 out - n/a
h2/16 brown brake shutdown in - tap to brake wire switch above pedal
h2/17 grey hood pin - to hood pin
h2/18 violet yellow starter out - is this needed?not needed
h2/19 blue instant trigger in - connect to the other sensors
h2/20 grey/black diesel wait to start - is this needed? Not needed
h2/21 white/blue remote start/tt acvt in - is this needed? only if you want push button start or turbo timmer
h2/22 orange acc out - is this needed? Not needed
h2/23 violet/white tach in - tap to car's tach
h2/24 oem alarm out - n/a

remote start 10 pin heavy gauge really confused with harness

h3/1 pink ign in/out (+) - tap to ign or const 12v?
h3/2 red/white fused ign2/flex relay in - is this needed? 12 volts
h3/3 orange acc out - tap car's acc
h3/4 violet start out - cut starter wire then connect this to starter side
h3/5 green starter in - key side of cut starter wire
h3/6 red ign in (+) - tap to ign? 12 volts
h3/7 pink/white ign2 out - where to tap this?
h3/8 pink/black flex relay in - is this needed? Not needed
h3/9 red/black acc/starter in - tap to const 12v12 volts

Originally Posted by larueminati

hi, im attempting to install a viper 5704 alarm system on auto 96 integra and i need help to figure out what wires/connections do not need to be used and where some wires go. feel free to make corrections if i am wrong, and please help answer some of my questions (in bold)

thank you in advance

(took this list from Orange_SIR1)

Main Harness 6 pin

h1/1 red const 12v - tap to a const 12v source
h1/2 black grnd - chassis ground
h1/3 brown siren out - connect to direct to siren
h1/4 white/brown park light isolation wire - is this needed?no
h1/5 white park light out - tap to park lightsmake sure the small 10a fuse goes from the middle to the + on the module
h1/6 orange ground when armed output - where to ground this?this is only needed for fuel cut offs/etc don't need

Door lock 3 pin

1 blue out - tap to neg unlock
2 n/a
3 green - tap to neg lock

Aux/shutdown/trigger harness, 24 pin

h2/1 pink/white ign/flex relay out - where to tap this?not needed if setting up remote start. gets the ign input from the thick gauge
h2/2 black/white neutral safety input - tap to e brake?yes
h2/3 blue white 2nd stat/rear defog out - tap to defogger
h2/4 green black oem alarm disarm out - n/a
h2/5 red/white trunk release out - tap to trunk release
h2/6 green door trigger input (-) - tap this to where?
h2/7 black/yellow dome light supv out - connect to relay/lights
h2/8 brown/black horn honk - tap to hornmight need relay. most don't use
h2/9 dark blue status out - where to connect this?don't need
h2/10 pink ign out - where to connect this?same as pink. only needed if remote start thick gauge aren't used.
h2/11 white/black aux3 out - n/a
h2/12 violet (+) door trigger in - where to connect this?not needed since honda door trigger inputs are (-) which is why you use the green wire
h2/13 white/violet aux1 out - n/a
h2/14 violet/black aux2 out - n/a
h2/15 orange/black aux4 out - n/a
h2/16 brown brake shutdown in - tap to brake wire switch above pedal
h2/17 grey hood pin - to hood pin
h2/18 violet yellow starter out - is this needed?same as the ignition. only needed if remote start isn't hooked up
h2/19 blue instant trigger in - connect to the other sensors
h2/20 grey/black diesel wait to start - is this needed?no
h2/21 white/blue remote start/tt acvt in - is this needed?no
h2/22 orange acc out - is this needed?no
h2/23 violet/white tach in - tap to car's tach
h2/24 oem alarm out - n/a

remote start 10 pin heavy gauge really confused with harness

h3/1 pink ign in/out (+) - tap to ign or const 12v?ignition
h3/2 red/white fused ign2/flex relay in - is this needed?no
h3/3 orange acc out - tap car's acc
h3/4 violet start out - cut starter wire then connect this to starter side
h3/5 green starter in - key side of cut starter wire
h3/6 red ign in (+) - tap to ign?
h3/7 pink/white ign2 out - where to tap this?
h3/8 pink/black flex relay in - is this needed?
h3/9 red/black acc/starter in - tap to const 12v