Help with Viper 5901 Installation on 98 Civic
#1
Help with Viper 5901 Installation on 98 Civic
Using page 9 of this for my car: http://alarmsellout.com/support/diag...01988-2006.pdf
And for the Viper 5901 harnesses:
http://www.directeddealers.com/manua...2008_08web.pdf
So I've been trying to install the Viper 5901 on my 98 Civic since yesterday and so far I have these connected:
Viper 5901 -------------------Car's wire color
H1/2 12V CONSTANT INPUT -> White IGN wire
HI/3 SIREN OUTPUT -> Red wire from siren and grounded to bolt
H1/5 CHASSIS GROUND -> Grounded to bolt behind driver's kick.
H1/8 DOOR TRIGGER INPUT -> LT. Green/Red behind radio
H1/11 PARKING LIGHT OUTPUT -> Red/Black wire above fuse box
H2 NOT USED
Door lock harness, 3-pin connected
1] BLUE (+) LOCK (-) (Both from behind the radio's green harness)
3] GREEN (-) LOCK (+)
H3/4 STARTER OUTPUT (Connected to car side)
H3/5 STARTER INPUT (Connected to key side)
This is all I've connected for now, I just wanted to test out the lock/unlock with the remote.
I can hear chirp (or just a noise) coming from the siren when I plug the H1 harness into the brain, but the problem is, no light whatsoever on the control center ever turns on. When I measured the voltage across the command center, it read as ~5V. Is this right? Or should it be 12V?
Maybe I have to finish connecting all the other wires first?
And for the Viper 5901 harnesses:
http://www.directeddealers.com/manua...2008_08web.pdf
So I've been trying to install the Viper 5901 on my 98 Civic since yesterday and so far I have these connected:
Viper 5901 -------------------Car's wire color
H1/2 12V CONSTANT INPUT -> White IGN wire
HI/3 SIREN OUTPUT -> Red wire from siren and grounded to bolt
H1/5 CHASSIS GROUND -> Grounded to bolt behind driver's kick.
H1/8 DOOR TRIGGER INPUT -> LT. Green/Red behind radio
H1/11 PARKING LIGHT OUTPUT -> Red/Black wire above fuse box
H2 NOT USED
Door lock harness, 3-pin connected
1] BLUE (+) LOCK (-) (Both from behind the radio's green harness)
3] GREEN (-) LOCK (+)
H3/4 STARTER OUTPUT (Connected to car side)
H3/5 STARTER INPUT (Connected to key side)
This is all I've connected for now, I just wanted to test out the lock/unlock with the remote.
I can hear chirp (or just a noise) coming from the siren when I plug the H1 harness into the brain, but the problem is, no light whatsoever on the control center ever turns on. When I measured the voltage across the command center, it read as ~5V. Is this right? Or should it be 12V?
Maybe I have to finish connecting all the other wires first?
#2
Honda-Tech Member
iTrader: (1)
Join Date: Oct 2005
Location: 99 probs but a stolen car aint 1, ca, cerritos/fullerton
Posts: 9,716
Likes: 0
Received 3 Likes
on
3 Posts
Re: Help with Viper 5901 Installation on 98 Civic
From the sounds of this. Its not a planned out install. You have wires going all over the place.. But to answer your question. MAke sure the fuse is going into the 12 output on the brain.
#3
Re: Help with Viper 5901 Installation on 98 Civic
Nevermind, used the old remote and everything worked fine for some reason. Now the 2 way one works perfectly as well.
Thanks anyways!
Thanks anyways!
Thread
Thread Starter
Forum
Replies
Last Post
DisOnesAPlaya
Audio / Security / Video
9
01-13-2011 04:14 PM