B16 build up...pics
#1
Honda-Tech Member
Thread Starter
Join Date: Aug 2003
Location: Houston, tx, 77029
Posts: 242
Likes: 0
Received 0 Likes
on
0 Posts
11.7 B16 build up...pics & video
Here are some pictures of a B16 build up that my buddy Huy(crx=si) has been working on. All of the labor and fabrication was done by Huy. I'll let Huy post all the specs...its 3am and I don't remember them all...
There is a Hytech header in one of the pictures...it was not used on this car. The header used was made by Huy.
Preliminary HP numbers are in the 240s.
Modified by 20lbbooster at 4:07 AM 10/15/2006
Modified by 20lbbooster at 4:19 PM 10/15/2006
There is a Hytech header in one of the pictures...it was not used on this car. The header used was made by Huy.
Preliminary HP numbers are in the 240s.
Modified by 20lbbooster at 4:07 AM 10/15/2006
Modified by 20lbbooster at 4:19 PM 10/15/2006
#5
Honda-Tech Member
Join Date: Aug 2005
Location: houston, tx, usa
Posts: 477
Likes: 0
Received 0 Likes
on
0 Posts
Re: (SioneSi)
86mm 13.5:1 custom supertech pistons
89mm balanced LS crank
golden eagle sleeves
maxlight B16a Manley rods
supertech valvetrain
crane roller rockers/ roller cams
440 RC
TWM ITB
ported the head by me
header by me
tuned on Crome by me
4.9 ATS
tilton twin discs
that's all I can think for now, power in the 240s whp, I'll find the dyno graph, very conservative tuned, mixture still in the mid 12s with 110 gas (probably change to lower octane on the next tune), something is not right, power should be higher than my old 84 x 89 b16 setup, I just need to figure it out, I'm too tire, it's 3AM @ Stoopidfast dyno
89mm balanced LS crank
golden eagle sleeves
maxlight B16a Manley rods
supertech valvetrain
crane roller rockers/ roller cams
440 RC
TWM ITB
ported the head by me
header by me
tuned on Crome by me
4.9 ATS
tilton twin discs
that's all I can think for now, power in the 240s whp, I'll find the dyno graph, very conservative tuned, mixture still in the mid 12s with 110 gas (probably change to lower octane on the next tune), something is not right, power should be higher than my old 84 x 89 b16 setup, I just need to figure it out, I'm too tire, it's 3AM @ Stoopidfast dyno
Trending Topics
#9
Honda-Tech Member
Thread Starter
Join Date: Aug 2003
Location: Houston, tx, 77029
Posts: 242
Likes: 0
Received 0 Likes
on
0 Posts
Re: B16 build up...pics (20lbbooster)
#12
Honda-Tech Member
Join Date: Aug 2005
Location: houston, tx, usa
Posts: 477
Likes: 0
Received 0 Likes
on
0 Posts
Re: B16 build up...pics (biotech0123)
went to the track, made a couple shake down passes, first pass the car started to miss fire, let off after the 60' mark, cut 1.72 60', changed to some slightly hotter plugs, ran 11.7 @ 117mph bouncing rev limitter spinning into 2nd gear, cut 1.8 60', tried to make the 3rd pass but the engine have a little oil leak from the oil pressure switch , decided to call it a night.......this coming sunday, I'll try to cut some low 1.6 60' and hope for
11.3 -11.5, my buddy will post the vid shortly
11.3 -11.5, my buddy will post the vid shortly
#13
Honda-Tech Member
Thread Starter
Join Date: Aug 2003
Location: Houston, tx, 77029
Posts: 242
Likes: 0
Received 0 Likes
on
0 Posts
Re: B16 build up...pics (20lbbooster)
#17
Honda-Tech Member
Thread Starter
Join Date: Aug 2003
Location: Houston, tx, 77029
Posts: 242
Likes: 0
Received 0 Likes
on
0 Posts
Re: (C1CRX)
yeah, he made that traction bar too. All the fabrication and labor was done 100% in house.
The car weighs in at 1950lbs with driver.
The car weighs in at 1950lbs with driver.
#24
Junior Member
Join Date: Nov 2004
Location: makaha, hawaii, united states
Posts: 867
Likes: 0
Received 0 Likes
on
0 Posts
Re: (black cx)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by black cx »</TD></TR><TR><TD CLASS="quote">thats a monster</TD></TR></TABLE>