208hp N/A GSR catch can questions
#1
Honda-Tech Member
Thread Starter
Join Date: Oct 2009
Location: Inland Empire
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
208hp N/A GSR catch can questions
I have a freshly rebuilt 96 jdm gsr engine & 96 ITR tranny, skunk2 tuner 2 cams with dual valve springs & retainers & stock cam gears,JDM ITR 98 spec 4-1 header with matching 2.5 ITR CAT & 2.5" exh piping to ITR Muffler, ITR intake tube / Apexi power intake, AEM FPR & RAIL, H22A4 injectors, ACT streetlight flywheel, Exedy clutch. Ok when rebuilding the engine every part was meticulosly cleaned, every seal, gasket, bearing was replaced ie main & rod bearings (acl) I had the head redone & valve job & new valve stem seals replaced (oem) I re-used the jdm gsr pistons the engine came with, do to the higher compresion jdm vs usdm, but I did hone the block & install new oem Honda rings. Engine made good power 208hp @ Churches Automotive testing
OK the problem im having is im getting black crap all over my back bumper EVERY day once its warmed up it clears out & becomes very minimal. Other issue I go through A LOT of oil ive only used non synthetic Castrol Gtx both 5w30 & 10w30, I was told by a reputable member on here that my engine has too much pressure & that I should get a catch can to catch the oil vapors before they enter my intake & back out my exh onto my bumper. I obviously have blow by from the hose that goes from my valve cover to my intake tube so question is is this a solution, if so. What's the best catch can set up for me & do you think this will help my oil consuption & crap on the back of my car. It does smoke when im really on it & smells inside my car too. I have around 10k on engine since rebuild swap is in my 99 gs integra
OK the problem im having is im getting black crap all over my back bumper EVERY day once its warmed up it clears out & becomes very minimal. Other issue I go through A LOT of oil ive only used non synthetic Castrol Gtx both 5w30 & 10w30, I was told by a reputable member on here that my engine has too much pressure & that I should get a catch can to catch the oil vapors before they enter my intake & back out my exh onto my bumper. I obviously have blow by from the hose that goes from my valve cover to my intake tube so question is is this a solution, if so. What's the best catch can set up for me & do you think this will help my oil consuption & crap on the back of my car. It does smoke when im really on it & smells inside my car too. I have around 10k on engine since rebuild swap is in my 99 gs integra
#3
Honda-Tech Member
Thread Starter
Join Date: Oct 2009
Location: Inland Empire
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Re: 208hp N/A GSR catch can questions
Ok but if I remember correctly, I believe on there set-up is a block style catch can, I think in there kit they suppy nipples that screw into the block, Ideal for turbo applications, correct me if im wrong.
Did u think that the catch can is gonna help my problem ?
Did u think that the catch can is gonna help my problem ?
#5
Honda-Tech Member
Thread Starter
Join Date: Oct 2009
Location: Inland Empire
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Re: 208hp N/A GSR catch can questions
Thread
Thread Starter
Forum
Replies
Last Post
99gsvtec
All Motor / Naturally Aspirated
19
04-13-2010 02:58 PM